Part-code reference

• ACC01Spray-applied pickup bed linerAccessories and trim+

  Identify the repair area and document why the existing bed coating requires restoration. Check the estimate for overlapping work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
  • Retain the relevant service record or supplier documentation.
• ACC02Pickup cap removal and installationAccessories and trim+

  Record the access need and the cap attachment points affected by the repair. Check whether another operation already includes this work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• ACC03Front license plate removal and installationAccessories and trim+

  Identify the front plate and its attachment. Include this as a separate consideration only when the repair scope and estimating inclusions support it.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
• ACC04Tailgate license plate removal and installationAccessories and trim+

  Record the need to remove the plate from the tailgate and check whether the tailgate operation already covers it.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
• ACC05Trunk-lid license plate removal and installationAccessories and trim+

  Identify the plate mounted on the trunk lid and check the related panel operation before treating removal as additional work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
• ACC06Rear-bumper license plate removal and installationAccessories and trim+

  Identify the plate mounted on the rear bumper. Check the bumper operation for included removal and installation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
• ACC07Left running board removal and installationAccessories and trim+

  Document the access or repair need on the left side. Check the attachment requirements and any overlap with the panel operation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• ACC08Right running board removal and installationAccessories and trim+

  Document the access or repair need on the right side. Check the attachment requirements and any overlap with the panel operation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• ACC09Rigid pickup-bed cover removal and installationAccessories and trim+

  Identify the rigid cover and explain why it must be removed for the repair. Review its mounting instructions.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• ACC10Flexible pickup-bed cover removal and installationAccessories and trim+

  Identify the flexible cover and its mounting system. Document why removal is needed and check for included access work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• ACC11Door-edge protective trim replacementAccessories and trim+

  Record the affected door-edge trim and why it cannot be reused. Check whether it is supplied with another replacement part.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• BDY01Access work for collision repairsBody and vehicle protection+

  Identify the specific obstruction and the access work required. Avoid an unspecified allowance or duplication of another removal operation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• BDY02Cleanup after restraint deploymentBody and vehicle protection+

  Document the affected area and residue. Determine the appropriate handling and cleaning requirements before planning the work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• BDY03Interior spill cleanup related to the repairBody and vehicle protection+

  Record the spill location, material and relationship to the repair. Distinguish required cleanup from unrelated interior detailing.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• BDY04Exterior vehicle coveringBody and vehicle protection+

  Identify the surfaces requiring protection and the repair activity that makes covering necessary. Check for masking already included elsewhere.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• BDY05Temporary covering of a damaged openingBody and vehicle protection+

  Document the exposed opening and the need for temporary weather protection. Describe the material without specifying a brand.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• BDY06Exterior protection during weldingBody and vehicle protection+

  Identify exposed exterior surfaces and document the protection required for the planned welding work. Confirm applicable vehicle and equipment instructions.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• BDY07Interior protection during weldingBody and vehicle protection+

  Identify interior components that need protection for the planned work. Confirm the protection requirements before repairs begin.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• BDY08Broken-glass cleanupBody and vehicle protection+

  Record where glass fragments are present and the cleanup scope. Distinguish this work from glass removal and general detailing.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• BDY09Vehicle cleaning before repairBody and vehicle protection+

  Document the condition that prevents inspection or repair and the cleaning needed to address it. Check for cleaning included in preparation operations.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• BDY10Interior and component protection during repairBody and vehicle protection+

  Identify the components at risk from the specific repair process. Describe the protection needed and check for overlap with other covering or masking.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
• BDY11Seat-belt system inspectionBody and vehicle protection+

  Confirm the vehicle-specific inspection requirements that apply after this event. Record the findings and distinguish inspection from any required replacement.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• BDY12Supplemental restraint system inspectionBody and vehicle protection+

  Determine the applicable manufacturer inspection requirements. Document the affected components and findings without treating a visual check as proof of system readiness.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• DIA01Driver-assistance system calibrationDiagnostics and calibration+

  Identify the system and the repair event that may trigger calibration. Verify the exact requirement and retain the calibration result.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA02Road procedure for driver-assistance calibrationDiagnostics and calibration+

  Confirm whether the particular system requires a road-based calibration procedure. Identify its scope and distinguish it from a general road test.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA03Low-voltage battery support during diagnosticsDiagnostics and calibration+

  Confirm whether the planned diagnostic or programming work requires battery support. Document its use and check whether the service already includes it.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• DIA04Coordination of pre-repair and post-repair scansDiagnostics and calibration+

  Identify any actual coordination work and distinguish it from the scan service itself. Check for duplication in the selected scan operation or supplier charge.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Retain the relevant service record or supplier documentation.
• DIA05Steering-angle sensor initializationDiagnostics and calibration+

  Verify whether the repair requires steering-angle initialization and whether an alignment or calibration service already includes it. Retain the service result.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA06Post-repair road verificationDiagnostics and calibration+

  Document the specific post-repair concern or requirement being checked. Confirm the vehicle is ready for the procedure and retain the result.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA07Diagnostic road evaluationDiagnostics and calibration+

  Identify the reported condition and the reason for a road evaluation. Distinguish diagnostic evaluation from a separate post-repair verification.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA08Post-repair diagnostic scanDiagnostics and calibration+

  Verify the post-repair scanning requirements for the vehicle and repair. Retain the scan results and distinguish scanning from further diagnosis or calibration.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA09Pre-repair diagnostic scanDiagnostics and calibration+

  Verify the pre-repair scanning requirements and retain the results used to plan the repair. Distinguish the scan from subsequent diagnosis of a reported fault.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• DIA13Occupant-detection system initializationDiagnostics and calibration+

  Identify the affected occupant-detection system and verify any inspection, initialization or calibration requirement for the repair. Retain the applicable results.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• ELE01Battery electrolyte cleanupElectrical and battery+

  Identify the affected area and verify the handling requirements for the battery chemistry involved. Document the cleanup scope without assuming a universal procedure.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• ELE02High-voltage battery charging or charge maintenanceElectrical and battery+

  Confirm the vehicle-specific need and authorized method for charge maintenance during the repair. Keep the charging record distinct from other battery operations.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• ELE03Low-voltage battery disconnection and reconnectionElectrical and battery+

  Verify the vehicle requirements and any related initialization work. Check whether the main repair operation already includes disconnection and reconnection.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• ELE04High-voltage system isolation and restorationElectrical and battery+

  Verify the manufacturer procedure, required qualifications and documentation for the specific vehicle. The reference entry does not provide an isolation procedure.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• ELE05Wiring moved temporarily for repair accessElectrical and battery+

  Identify the harness or wiring affected, the access need and the required protection. Check whether another removal operation includes this access.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• ELE06Wiring repairElectrical and battery+

  Identify the damaged circuit and verify whether the manufacturer permits the proposed repair. Document the repair method by reference to the applicable procedure.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FLD01Engine coolantFluids and refrigerants+

  Identify coolant lost or required because of the repair. Verify the specified fluid and determine the actual quantity from the work performed.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FLD02Brake fluidFluids and refrigerants+

  Document why the repair requires brake fluid and confirm the vehicle specification. Check the related service for included material.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FLD03Engine oilFluids and refrigerants+

  Identify the repair-related need and specified oil. Use the actual service documentation rather than a preset material allowance.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FLD07Transmission fluidFluids and refrigerants+

  Confirm the transmission and required fluid specification. Document the repair-related use and check for material already included in the service.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FLD08Power-steering fluidFluids and refrigerants+

  Verify that the vehicle uses a fluid-based steering system and identify the specified fluid. Document the actual repair-related requirement.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FLD09R-1234yf refrigerantFluids and refrigerants+

  Verify the refrigerant specified for the vehicle and retain the service record. Base any quantity on documented service use.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FLD10Air-conditioning leak checkFluids and refrigerants+

  Document the reason for leak testing and the applicable method. Check whether the related air-conditioning service includes this test.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FLD11R-134a refrigerantFluids and refrigerants+

  Verify the refrigerant specified for the vehicle and retain the service record. Check for refrigerant already included in the related service.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FLD12Washer fluidFluids and refrigerants+

  Identify the repair-related fluid loss or replacement need. Document the material used and avoid adding routine replenishment without a repair basis.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
• FRM01Preliminary structural pullStructural work and equipment+

  Identify the damage and purpose of the preliminary pull. Verify repairability and the applicable structural repair plan before selecting the operation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FRM02Structural equipment setup and measurementStructural work and equipment+

  Identify the measurement or anchoring setup required by the repair plan. Distinguish setup, measurement and corrective work in the documentation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FRM03Equipment setup for a body pullStructural work and equipment+

  Document the body-pull setup and why it differs from any structural setup already listed. Check the equipment and vehicle requirements.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FRM04Unibody dimensional correctionStructural work and equipment+

  Confirm that the planned correction is permitted and supported by measured damage. Retain the relevant dimensional records.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FRM05Frame dimensional correctionStructural work and equipment+

  Confirm the frame construction, repairability and measured damage. Document the permitted corrective work and its verification.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• FRM06Riveting equipment setup and verificationStructural work and equipment+

  Identify the joining process and its equipment setup or verification requirements. Keep the verification record relevant to the actual repair materials.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FRM07Restoration of anchoring contact areasStructural work and equipment+

  Identify any areas affected by approved anchoring and the required restoration. Verify the permitted attachment method and restoration requirements.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• FRM08Welding equipment setup and verificationStructural work and equipment+

  Identify the approved joining process and its setup or verification requirements. Retain the relevant verification documentation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• GLS01Back-glass bonding materialsGlass and sealing+

  Identify the glass application and specified bonding system. Check for materials supplied with the glass or included in an outside service.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• GLS02Existing glass adhesive removalGlass and sealing+

  Identify the location and adhesive-removal scope. Follow the applicable glass and bonding-system requirements and check for included preparation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• GLS05Side-glass bonding materialsGlass and sealing+

  Identify the bonded side-glass application and required materials. Check the replacement part and service documentation for included supplies.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• GLS06Windshield bonding materialsGlass and sealing+

  Verify the required bonding system for the windshield application. Check for materials already included in a glass service or supplied kit.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• GLS07Glass-edge masking for refinishingGlass and sealing+

  Identify the glass edge requiring protection and the specific refinish scope. Confirm that masking is appropriate and not already included.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• GLS08Post-repair water-leak checkGlass and sealing+

  Identify the repaired opening or sealing area and the reason for a water-leak check. Document the test scope and findings.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• MAT01Adhesion-promoting treatmentRepair materials+

  Identify the substrate and coating system that require an adhesion-promoting product. Check for material or application already included in another operation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• MAT02Plastic repair materialRepair materials+

  Identify the plastic component, approved repair approach and materials used. Verify compatibility with the substrate and finishing system.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT03Cavity corrosion-protection materialRepair materials+

  Identify the repair areas requiring cavity protection and the specified material. Document access and application without assuming every repair requires it.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT04Cutting discs used in the repairRepair materials+

  Document repair-related cutting-disc use and check the estimating or service basis for separately itemized consumables.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• MAT05Epoxy primer materialRepair materials+

  Identify the substrate and repair stage requiring epoxy primer. Check the coating-system instructions and avoid duplicating other primer entries.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• MAT06Flexible-coating additiveRepair materials+

  Verify whether the actual coating system and component require an additive. Do not assume all flexible components use the same product system.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• MAT07Acoustic foam installationRepair materials+

  Identify the location, foam function and specified replacement material. Distinguish acoustic foam from structural products.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT08Existing acoustic foam removalRepair materials+

  Identify the acoustic foam that must be removed for the repair and its removal scope. Check for access work already included elsewhere.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT09Existing sound-damping pad removalRepair materials+

  Identify the affected pad and reason for removal. Review related panel preparation for included removal work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT10Sound-damping pad replacementRepair materials+

  Identify the replacement pad location and required function. Check whether the pad is supplied with a replacement panel.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT11Panel-bonding adhesiveRepair materials+

  Identify the approved panel-bonding application and adhesive specification. Document the material used without treating the entry as permission to substitute joining methods.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT12Repair-area corrosion protectionRepair materials+

  Identify the protection disturbed by the repair and the required restoration. Check for overlap with primers, cavity materials and seam sealing.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT13Abrasive belts used in the repairRepair materials+

  Document repair-related abrasive-belt use and check the basis for separately itemized consumables.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• MAT14High-build seam-sealing materialRepair materials+

  Identify the seam, required profile and approved material. Check for overlap with other seam-sealer entries.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT15Seam-sealing materialRepair materials+

  Identify the seam and applicable sealing requirements. Specify the material actually needed rather than a general allowance.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT16Flowable seam-sealing materialRepair materials+

  Identify the seam and confirm that a flowable product is appropriate for its application. Document the required material and avoid duplicate sealing entries.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT17Urethane seam-sealing materialRepair materials+

  Identify the required application and confirm product compatibility. Check the repair plan for another entry covering the same sealing work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT18Applied sound-damping treatmentRepair materials+

  Identify the affected sound-damping treatment and its restoration scope. Distinguish an applied coating from replacement pads or foam.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT19Structural foam installationRepair materials+

  Verify the specified structural product, location and repair requirements. Do not substitute acoustic foam or infer a procedure from this reference.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• MAT20Weld-through corrosion-protection primerRepair materials+

  Verify whether the approved joining process calls for this product at the specific location. Check product compatibility and related preparation inclusions.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• RFN02Refinish color adjustmentRefinish preparation and finishing+

  Document the color-match issue and the adjustment work performed. Check whether a more specific color-verification entry covers the same work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN03Paint-finish defect correctionRefinish preparation and finishing+

  Identify the finish defect, affected area and correction scope. Check the coating-system guidance and any included finish work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN04Repair-edge featheringRefinish preparation and finishing+

  Identify the repaired area and feathering scope. Check for overlap with a combined preparation operation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN05Repair-area feathering, priming and blockingRefinish preparation and finishing+

  Document the combined preparation scope and affected area. Avoid duplicating individual feathering or primer-preparation entries.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN06Stone-impact protective coating applicationRefinish preparation and finishing+

  Identify the area and texture requiring restoration. Verify the compatible coating system and related refinish scope.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• RFN07Existing stone-impact protective coating removalRefinish preparation and finishing+

  Identify the coating and removal needed for the repair. Check whether the panel or coating preparation already includes this work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN08Three-stage color verification panelRefinish preparation and finishing+

  Confirm the coating system and the need for a color-verification panel. Document the verification work and avoid overlap with general color adjustment.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN09Four-stage color verification panelRefinish preparation and finishing+

  Identify the coating system and the color-verification work required. Record the verification scope separately from duplicated tinting entries.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN10Door-opening maskingRefinish preparation and finishing+

  Identify the door opening and refinishing activity requiring protection. Check for overlap with general opening or jamb masking.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN11Engine-compartment maskingRefinish preparation and finishing+

  Identify the compartment surfaces requiring protection for the planned refinishing. Review the related preparation inclusions.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN12Masking for primer applicationRefinish preparation and finishing+

  Identify the primer area and adjacent surfaces requiring protection. Check whether the relevant preparation operation includes this masking.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN13Jamb and opening maskingRefinish preparation and finishing+

  Identify each opening or jamb requiring protection and the reason. Avoid duplication with a more specific opening-masking entry.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN14Trunk-opening maskingRefinish preparation and finishing+

  Identify the trunk opening and the planned refinish scope. Check for masking already included in related preparation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN15Primer application and blockingRefinish preparation and finishing+

  Document the repaired area and primer-preparation scope. Check for duplication with a combined feather, prime and block entry.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN16Primer color adjustmentRefinish preparation and finishing+

  Verify the coating-system requirement for primer color and document any adjustment performed. Check the related preparation for included work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN19Unprimed flexible-part preparationRefinish preparation and finishing+

  Identify the supplied part condition and specified preparation system. Verify the substrate requirements and check for included preparation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• RFN20Finish sanding and polishingRefinish preparation and finishing+

  Identify the area, finish objective and actual work performed. Distinguish this operation from localized defect correction and included finish work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN21Masking for seam-sealer applicationRefinish preparation and finishing+

  Identify the seam and adjacent areas requiring protection. Check whether the sealing or preparation operation includes the masking.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• RFN22Masking for stone-impact coating applicationRefinish preparation and finishing+

  Identify the coating boundary and protection needed. Check for overlap with other masking for the same application.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• STR01Blackout film replacementStripes, tape and adhesive+

  Identify the affected decorative film and replacement scope. Check whether the replacement part already includes the film.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• STR02Adhesive-tape renewal for a reusable componentStripes, tape and adhesive+

  Identify the reusable component and the tape-renewal requirement. Check the removal operation and part supply for included material or preparation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• STR03Painted pinstripe restorationStripes, tape and adhesive+

  Document the existing stripe and repair-related restoration scope. Retain relevant outside-service documentation when applicable.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
  • Retain the relevant service record or supplier documentation.
• STR04Adhesive pinstripe replacementStripes, tape and adhesive+

  Identify the affected stripe and the actual replacement scope. Verify the product and avoid assuming a preset number of pieces per panel.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• STR05Adhesive residue removalStripes, tape and adhesive+

  Identify the residue and why it must be removed. Check whether the related trim, stripe or film operation includes cleanup.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• STR06Emblem and remaining adhesive removalStripes, tape and adhesive+

  Identify the affected emblem and adhesive-removal scope. Check whether the replacement or refinishing operation already includes this work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.
• STR07Existing adhesive pinstripe removalStripes, tape and adhesive+

  Identify the stripe and repair-related removal area. Check for removal already included with replacement or panel preparation.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify the applicable material or equipment instructions.
• SVC04Movement of a disabled vehicle for repair accessVehicle handling+

  Document why the vehicle cannot move normally and the movement required for the repair. Distinguish this work from ordinary movement through the facility.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
• SVC06Vehicle transport for an outside repair serviceVehicle handling+

  Identify the required outside service and transport need. Retain the related record and check for transport included in the service.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Retain the relevant service record or supplier documentation.
• WHL01Four-wheel alignmentWheels and alignment+

  Verify the repair-related alignment requirement and retain the measurement record. Check the service scope for included sensor initialization or other work.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• WHL02Wheel and tire balancingWheels and alignment+

  Identify the affected wheel and repair-related balancing need. Check whether tire installation or another service already includes balancing.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• WHL03Tire installation and balancingWheels and alignment+

  Identify the tire, wheel and repair-related service scope. Check for overlap with separately listed balancing or related material.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Retain the relevant service record or supplier documentation.
• WHL05Tire valve replacementWheels and alignment+

  Identify the valve type and reason for replacement. Check whether the tire service or pressure-monitoring component includes the required valve.

  Before adding it

  • Confirm that the operation applies to this repair.
  • Check the current estimating-system inclusions and overlapping work.
  • Document the need, location and work performed.
  • Verify current vehicle-specific manufacturer procedures and requirements.
  • Verify the applicable material or equipment instructions.